World Marketing Kerosene Heater Wick Chart

Replacement cartridge, for 2A700-A 10 micron wool felt, center core bond to prevent media migration, removes moisture, solids and other impurities from fuel oil. Compatible with fuel oil conforming to ASTM D396-09 (up to B5). 88CR - 10 GPH firing rate - for 77B, 1A-25B, 1A-25A.

Constructed from spun fiber. Designed to filter oil in a heating application. For FUL-FLO FB-4 filtration system. Boiler replacement part, complete with gaskets. Gear-tooth design. Compatible with fuel oil conforming to ASTM D396-09 (up to B5). RF-1 Micro Fiber Replacement Cartridges - for 77B, 1A-25B, 1A-25A.

10-micron wool felt. Center core bonded to prevent media migration.

Necessary for transfer of fuel from storage tank to heater. Easy to operate utilizing a large ball type siphon. Compatible with all types of kerosene heaters.

Male pipe thread x left hand male thread.

Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.

10-micron wool felt. Center core bonded to prevent media migration.

Male pipe thread x left hand male thread.

Pins in same direction as heating coil. Fits Dura Heat, Dyna-Glo, Envirotemp, Kero Heat*, Kero-World*. Fits many push type ignition assemblies. Redstone.

Pins in opposite direction of heating coil. Fits Aladdin, Comfort Glow, Corona, Kero-Sun, Kero Heat, Sears, Toyotomi.

Male pipe thread x left hand male thread.

Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.

Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.

Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.

Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.

Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.

Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.

Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.

Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.

Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.

Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.

Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.

Brass with stainless inserts with sintered filter.

Brass with stainless inserts with sintered filter.

1/8" angle MIP. Maximum operating pressure 5 PSI. Maximum pressure 10 PSI.

Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.

Produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively more hollow at higher flow rates. Provides smooth ignition and efficient combustion, particularly in larger burners.

Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.

Mainly used on burners with a hollow cone air pattern and for throughputs up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion.