1/2HP heavy duty split capacitor motor - high efficiency - low Amp draw, rugged cast iron construction, 10' grounded waterproof power cord, pumps up to 80 gallons per minute, 4800 gallons per hour, bottom intake provides for clog resistant suction, clog-free metal vortex impeller, tethered float switch with piggy back plug included, pump will lift water over 25 ft. vertical height, handles 2" solids, 2" female iron pipe discharge thread. Cast aluminum, non-clogging vortex impeller. One year warranty from Superior Pump Co.

1/2 HP cast iron submersible sewage pump. Max flow rate is 5700 GPH at 0 ft. Durable, cast iron submersible sewage pump. 2 in. NPT discharge capable of handling up to 2 in. solids. Ideal for basement or below grade installations.

Under-sink basin system with 1/3 HP sump pump - pumps up to 2880 GPH. Ideal for pumping washing machine, wet bar and air conditioning drainage without an in-ground basin. Heavy-duty 6 gallon structural foam drainage tank. Easy installation - eliminates need for expensive plumbing renovation. CSA certified.

Handles up to 20 percent of sand, solids, leaves, and debris without clogging. Semi-vortex urethane rubber impeller with shaft mounted agitator suspends solids and allows for pumping of sand and stringy material. Continuous duty, air filled copper wound motor with class B insulation. Built-in thermal protection prevents motor failure due to overloading, accidental run-dry, and single phasing in three phase units. Double inside mechanical seals with silicon carbide faces (both top and bottom) run in an oil filled chamber. Double shielded, permanently lubricated, high temperature C3 ball bearings rated for a B-10 life or 60,000 hours provide for extended operational life. 2 year commercial warranty.

Pump: 1/2 hp sewage pump (93501), cast iron, tethered, 2" discharge, cast aluminum vortex impeller, 7.6 amp, 10' cord. Includes: 18" x 30" basin, 18" cover, check valve and snap-in plug. Basin features: Structural foam construction, air tight molded reusable pvc, corrosion resistant, 4" inlet hub, 2" discharge and vent, 30 gal capacity, built in torque stops. Check valve features: heavy duty rubber boots, stainless steel clamps, full flow design, 2" connections. Snap-in hub features: heavy duty stainless steel clamp, water & vapor tight seal, fits 4" DWV schedule 40/80 pipe. .

Designed for residential and light commercial sewage applications. Ideal for basement or below grade installations. Maximum pumping capacity of 7680 GPH. Cast Iron motor and pump housing. Automatic operation with replaceable piggyback tether float switch. 2" discharge and capable of handling 2" NPT solids. Designed for 18" diameter or larger basins.

Automatic submersible sewage pump made from rugged cast-iron to maximize pump life. Heavy-duty motor with overload protection provides safe operation. Maximum pumping capacity to 9000 GPH. 2" NPT discharge and 10' power cord.  Requires 18" minimum diameter sewage basin. CSA certified.

115V, 10' cord, CSA and CUS listed, 13500 gph capacity, energy-efficient PSC motor, rust-proof impeller, 2" NPT discharge pipe, 2" maximum solid handling.

ALL COMPONENTS SOLD SEPARATELY. Rear discharge toilet and macerating pump system allows for an additional bathroom in a location with no under-the-floor plumbing. Macerator Pump Specifications 18.5" (470 mm) W x 11.5" (290 mm) h x 7" (175 mm), GPM: Max 60 (227 liters), .8 HP, 8A at 120V, 600W, 22 lbs (10 kg). Pump:980-4287. Round Bowl: 980-4303. Elongated Bowl: 980-4295. Tank: 980-4311.

4RLAG-2H Aluminum Water Transfer Pump. Powered by Commercial grade Honda GX120 engine. Durable cast iron semi-open style impeller. Lightweight aluminum casing includes HD roll frame. Self-priming to 25' of suction lift. Built-in check valve. EPA certified. 2" MNPT inlet and discharge.Max head 59 ft. Max flow 143 GPM.

Compact, reliable design. Heavy-duty Honda gas engine with oil sensor. High chrome impeller, cast iron volute casing, and stainless steel wear plate. Silicon carbide mechanical seal. Galvanized steel hose couplings provide increased durability and decreased maintenance. Durable rolled-steel frame provides pump/engine with maximum protection, ease of handling or transport, and safe operation. Pump/engine set mounted to cage frame on rubber vibration cushions to buffer stress and wear. 2 year commercial warranty.

Compact, reliable design. Heavy-duty Honda gas engine with oil sensor. High chrome impeller, cast iron volute casing, and stainless steel wear plate. Silicon carbide mechanical seal. Galvanized steel hose couplings provide increased durability and decreased maintenance. Durable rolled-steel frame provides pump/engine with maximum protection, ease of handling or transport, and safe operation. Pump/engine set mounted to cage frame on rubber vibration cushions to buffer stress and wear. 2 year commercial warranty. Rental.