Inexpensive, disposable test caps for pressure testing ABS or PVC with up to 10 pounds pressure. Cap is solvent welded inside open pipe end. After test the center is knocked out and thrown away. Made of ABS.

Inexpensive, disposable test caps for pressure testing ABS or PVC with up to 10 pounds pressure. Cap is solvent welded inside open pipe end. After test the center is knocked out and thrown away. Made of ABS.

Inexpensive, disposable test caps for pressure testing ABS or PVC with up to 10 pounds pressure. Cap is solvent welded inside open pipe end. After test the center is knocked out and thrown away. Made of ABS.

Inexpensive, disposable test caps for pressure testing ABS or PVC with up to 10 pounds pressure. Cap is solvent welded inside open pipe end. After test the center is knocked out and thrown away. Made of ABS.

For capping pipe ends. Convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. For temporary or permanent use. Can be use with any material. Suitable for underground use. Not for use on pressurized plumbing systems. Meets ASTM C-1173, C-1277, C1460, CISPI 310, IAPMO PS 109, PS90, & CSA B602.

Easy way to cap pipe ends, clean-outs and open test pipes. Made of flexible PVC, they're suitable for above ground or underground use, on cast iron, steel, copper or plastic piping. Designed to fit all drain, waste, and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten to 60" pounds torque. Complies with ASTM D5926.

For capping pipe ends. Convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. For temporary or permanent use. Can be use with any material. Suitable for underground use. Not for use on pressurized plumbing systems. Meets ASTM C-1173, C-1277, C1460, CISPI 310, IAPMO PS 109, PS90, & CSA B602.

Easy way to cap pipe ends, clean-outs and open test pipes. Made of flexible PVC, they're suitable for above ground or underground use, on cast iron, steel, copper or plastic piping. Designed to fit all drain, waste, and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten to 60" pounds torque. Complies with ASTM D5926.

Plastic mechanical plug designed to hold higher pressures.  Used for plugging open ended piping as protection from dirt, dust, or debris. Maximum allowed air is 5 PSIG

For capping pipe ends. Convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. For temporary or permanent use. Can be use with any material. Suitable for underground use. Not for use on pressurized plumbing systems. Meets ASTM C-1173, C-1277, C1460, CISPI 310, IAPMO PS 109, PS90, & CSA B602.

Plastic mechanical plug designed to hold higher pressures.  Used for plugging open ended piping as protection from dirt, dust, or debris. Maximum allowed air is 5 PSIG

Easy way to cap pipe ends, clean-outs and open test pipes. Made of flexible PVC, they're suitable for above ground or underground use, on cast iron, steel, copper or plastic piping. Designed to fit all drain, waste, and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten to 60" pounds torque. Complies with ASTM D5926.

Easy way to cap pipe ends, clean-outs and open test pipes. Made of flexible PVC, they're suitable for above ground or underground use, on cast iron, steel, copper or plastic piping. Designed to fit all drain, waste, and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten to 60" pounds torque. Complies with ASTM D5926.

For capping pipe ends. Convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. For temporary or permanent use. Can be use with any material. Suitable for underground use. Not for use on pressurized plumbing systems. Meets ASTM C-1173, C-1277, C1460, CISPI 310, IAPMO PS 109, PS90, & CSA B602.

Plastic mechanical plug designed to hold higher pressures.  Used for plugging open ended piping as protection from dirt, dust, or debris. Maximum allowed air is 5 PSIG

Plastic mechanical plug designed to hold higher pressures.  Used for plugging open ended piping as protection from dirt, dust, or debris. Maximum allowed air is 5 PSIG