Submit search
Used to change direction in piping and features lugs for fastening. Often used in conjunction with No.530671 washer hose valve for hooking up to automatic clothes washers and for fabricating water supply piping stub outs for toilet installation. Sometimes called a Drop Ear elbow.
Used in conjunction with a brass compression fitting to transition to a CPVC fitting. Replaces the ferrule.
Adapts from 1/2" CPVC to 1/2" male metal pipe thread and features lugs for fastening. Used on tub and shower faucets to adapt from 1/2" CPVC riser to shower arm. Sometimes called a Drop Ear elbow. Hand tighten only; seals by means of a special elastomeric gasket to ensure leakproof seal, use of joint compound or Teflon tape is neither necessary or recommended.
SLIP X SLIP Used to change direction in piping.
Solvent welds directly into 1/2'' CPVC fitting socket and adapts to female hose coupling.
Used to join straight lengths of CPVC tubing.
Used to provide a branch supply line from a main line.
Solvent welds directly onto 1/2" CPVC tubing and adapts mechanically to 3/8" O.D. PEX tubing or copper tubing. Most often used to adapt from 1/2" CPVC tubing risers through floor to 3/8" O.D. closet or lavatory riser tubes. Can also be used with metal risers.
Used to adapt to female metal threaded fittings in cold water applications only! Use Teflon tape to seal pipe threads. Do not use other materials or compounds unless specifically approved by manufacturer.
Allows a direct 90 degree connection between CPVC tubing and male running threads on faucet. Has a cone washer inside female end to achieve seal. Slip x female NPSM.
Unique molded CPVC/Stainless Steel design with internal "knurl" and EPDM O'ring insures reliability and integrity. Large Stainless steel hex for easy connection to IPS sized pipe and fittings. Meets/exceeds ASTM and ANSI standards. Pressure rated to 100 psi at 180 degrees F. Made with EverTUFF CPVC and Type 304 Stainless Steel.
Provides a 90 degree change in direction of the male running threads on a faucet. Has a cone washer inside female end to achieve seal. MALE NPSM X FEMALE NPSM.
Used to permanently or temporarily cap CPVC. Most often used in conjunction with short lengths of CPVC tubing to fabricate water hammer arrestors (air chambers) in the CPVC system. Bagged.
Used to reduce from fitting socket to CPVC tubing. Bagged.
Used to change direction in piping from a fitting socket. Also used in conjunction with a conventional CPVC 90 degree elbow to fabricate a change of direction of piping at any angle.
Used to join straight lengths of CPVC tubing to smaller size tubing.
Allows any fitting hub to be reduced to accept PEX, copper or CPVC tubing
Unique molded CPVC/Stainless Steel design with internal "knurl" and EPDM O'ring insures reliability and integrity. Large Stainless steel hex for easy connection to IPS sized pipe and fittings. Meets/exceeds ASTM and ANSI standards. Pressure rated to 100 psi at 180 degrees F. Made with EverTUFF CPVC and Type 304 stainless steel.
Solvent welds directly to CPVC tubing and provides a method for future disassembly of tubing without cutting.
Solvent welds directly onto 1/2" CPVC tubing and adapts mechanically to 3/8" OD Pex or copper tubing. Most often used to adapt from 1/2" CPVC tubing risers through the wall to 3/8" OD closet and/or lavatory riser tubes. Can also be used with metal risers.
90 degree elbow. CPVC/304 stainless steel technology with internal "knurl" and EDM. O'ring insuring reliability and integrity. Meets/exceeds all ASTM and ANSI standards. Made with Ever TUFF CPVC.
Designed to compensate for the difference in coefficients of expansion which exist between CPVC and metal pipe in hot water applications. Solvent welds directly to CPVC tube and adapts to standard male pipe threads. Use Teflon tape to seal pipe threads, do not use other materials or compounds unless approved by manufacturer.
