Designed for drainage in areas where waterproofing membrane is not required.  Plastic Snap-In Drain can be solvent welded or inserted into Sch. 40 DWV pipe.  One piece design does not allow for removal of the cover.

Rubber. For tip-toe style bathtub stoppers. 2-1/16" x 1" x 1/4".

4-1/4"  x 4-1/4" Stainless steel square tile ring. For use with the 151 Series Oatey drains.

Designed to fit 3-3/8" shower drains.

Designed for drainage in areas where waterproofing membrane is not required.  Plastic Snap-In Drain can be solvent welded or inserted into Sch. 40 DWV pipe.  One piece design does not allow for removal of the cover.

Steel construction, 2" diameter. Grid-style.

Designed for drainage in areas where waterproofing membrane is not required.  Plastic Snap-In Drain can be solvent welded or inserted into Sch. 40 DWV pipe.  One piece design does not allow for removal of the cover.

Strainer dome cover with screw.

Round design with screw holes 2" center-to-center. Includes adapter to replace one or two hole plates. Screws included.

Chrome plated face plate screws.

Steel construction, use with 3-1/8" drains. Screws not included.

2-15/16" diameter. Brushed nickel finish. Replaces Gerber no. 91-292.

Female threaded outlet, stainless steel grid, 3-1/2" flange diameter.

3-5/16" O.D. 6.88" h x 4-3/4" w.

Durable plastic construction. Designed to fit the Danco hair catcher for shower drains (Model #?s: 10533, 10529). Stops hair and other particles from going down the drain

2" PVC offset shower drain with receptor base. Solvent welds over 2" schedule 40 DWV pipe. Universal 4-1/4" Snap-Tite strainer. Drain body provides 1-1/2" offset to work around joists and imperfect slab penetrations. Drain body is sealed to shower base with rubber gasket and fiber slip washer.

For use on steel, fiberglass and other types of plastic shower bases. Solvent welds to 2" DWV or Schedule 40, ABS or PVC pipe. 4-1/2" flange diameter, with stainless steel grid.

Zinc body. Screws included.

For trip lever 6" eye wire. 10-32 brass eye bolt. Brass clevis plunger.

Plastic. Touch-toe design,

Includes screws. 2" center to center holes. Carded.

Threaded shaft.

Plumb Pak Tub Face Plate, 1-Hole, Trip lever Style, Suitable For Use With: Bath Drain, Chrome Plated

Plastic construction. Touch-toe design pushed to open and close. 2? diameter. Grid style to keep drain free from debris. Includes 3/8?and 5/16 screw studs.

Plumb Pak Tub Face Plate, 2-Hole, Blank Overflow, Suitable For Use With: Bath Drain, Chrome Plated

Designed for use with preformed shower stall bases.  The drain body is sealed to the shower base with a fiber and rubber washer.  2" Schedule 40 DWV pipe is secured with a mechanically compressed gasket that does not require caulking.  Drain top accommodates 4-1/4" Universal Snap-Tite strainers available in a variety of designer finishes. Compression gasket tightens around 2" Sch. 40 DWV pipe with caulking nut & wrench. Can be used with 1-1/2" Sch. 40 DWV pipe and 1-1/2" or 2" Copper DWV pipe when caulking gasket is replaced.

Fits 2" outlet.

4-1/4". For 101 PNC and 140 NC No-Calk snap-in shower drains, and 101 PS solvent weld and 2-part shower drains.Carded.

Designed for use with preformed shower stall bases.  The drain seals to the base with fiber and rubber washers.  2" Schedule 40 DWV pipe solvent welds to the drain base.  Drain top accommodates 4-1/4" universal Snap-Tite Strainers available in a variety of designer finishes. Drain body is sealed to shower base with rubber gasket and fiber slip washer.

Designed for use with preformed shower stall bases.  The drain seals to the base with fiber and rubber washers.  2" Schedule 40 DWV pipe solvent welds to the drain base.  Drain top accommodates 4-1/4" universal Snap-Tite Strainers available in a variety of designer finishes. Drain body is sealed to shower base with rubber gasket and fiber slip washer.