Drill/tap high-speed steel bit, split point with web thinning. High quality hex shank to ensure strong connection to drill chuck. Complete hole drilling, tapping and deburring/countersinking in one operation with power drill. Designed to tap up to 10 gauge metal. Back taper or deburr/countersink beyond tap to prevent thread damage from over-drilling.
Shorter for better access to tight spaces between studs and joists, will drill 2' and 4' joists. Self-feeding screw point draws bit through all wood types. Replaces special tools such as right angle drills and eliminates multiple steps to cut the hole to size. Overall length 4.5" (144mm) weight .3 lb. (118g). 1/4" hex. Over center single flute design for cleaner holes and less splintering. Marked with bit diameter and catalog number on shank for easy identification. Not for use in wood with nails.
Contains 100 anchors, 100 screws and a 1/4" masonry drill bit. For use in concrete, block, tile and brick. Moisture and chemical resistant, for indoor or outdoor use.
Replacement blade for Greenlee 0952-01 or 1940 flexible metal conduit cutter.
Keyhole saw with integrated blade and ergonomic handle design provides maximum strength. Hardened steel blade with clog-free teeth, handle with non-slip grip. Pointed tip easily punches through drywall. Blade cuts on both on push and pull strokes. Hole in handle for lanyard or convenient storage. Tool is not insulated. 11-5/8" overall length.
Poly line, 210 lb. average breaking strength, can be blown into conduit and then used to pull in a larger pulling rope, or it can be used directly to pull in smaller wires. Can be used directly from the container with power fishing systems. Resists tangling when dispensing. Prepunched hole for dispensing the line. Rot and mildew resistant.
For pulling single wire, cable or fish tape through walls. Clip attaches to hole in bit, mesh basket holds wire or cable during recovery, swivel reduces twisting.
Allows placement of the drill bit at any point within the wall. Helps in judging where the bit will be during drilling to avoid accidentally drilling through the wall. Use to position all bit and shaft sizes, vertical and horizontal.
Pen size, fits into pocket or tool pouch. Durable design to withstand the most severe environments. Comfort grip to ease fatigue. Bright LED and audible alarm if voltage is present. Twist of the cap ON/OFF switch for longer battery life. Use to detect the presence of voltage of 50-1000 volt AC at outlets, lighting fixtures, circuit breakers, wires and cables or to find a break in a wire. Replace batteries by pressing the release lever and twisting the top of the tester. Frequency: 50-500Hz. Cat IV, 600 volt per IEC 61010-1; Cat III, 1000 volt per UL 3111-1. Includes (2) 1.5 volt AAA batteries.
Steel fish tape in self-tensioning impact-resistant rewinder case with dirt-free tape finish. .045" thick, 2.75 pounds.
Cutting edge is hardened for longer life. Self-feeding screw point draws bit through wood even after multiple sharpenings. Made of high quality carbon alloy steel; cuts through nails and provides up to 3 times longer life. Overall length 18". Hex shank: 7/16" (11.1mm). Weight: 1.5 lb, (681g).
Pen size, fits into pocket or tool pouch. Detects power and voltage without touching the bare conductor. For use on power wiring plus lighting, thermostats and other low voltage circuits. Use to detect voltage in outlets, fixtures, wires and cables. Finds breaks in wires. Identifies hot and neutral conductors. Low battery indication. Voltage detection: AC 5-1000 volts. Frequency: 50-500Hz. Measurement category CAT IV, 1000 volts. Includes two 1.5 volt AAA batteries.
Use to measure voltage and check batteries, measure current of small electronic circuits. 600 volt AC/DC voltage. Resistance measurement. 1.5 volt/9 volt battery test. Continuity and diode tests. Built-in test leads and a rubber boot to protect meter from damage. 9 volt battery included. Measurement category: CAT III, 600 volt. ETL approved.
Three core products - the DM-25 manual ranging multimeter to measure voltage and check batteries, the GT-10 polarity cube to trouble shoot 120 volt AC grounded outlets and the GT-11 non-contact voltage detector for use in outlets, lighting fixtures, circuit breakers, wires and cables. Comes with a durable carrying case for storage and added protection.
Fits a 3/8" drill chuck and can be used with a cordless drill. Cuts perfect holes in drywall and ceiling tile. Cuts clean, precise holes that ensure no light leakage or poor-fitting installations. Self-sharpening, carbide-sprayed cutting tips cut dozens of holes in very abrasive materials and still stay sharp. Stabilizer spring balances cutting forces and offers more control of the tool when drilling drywall. Dedicated arbor and pilot drill eliminates changeover time. Included dust shield virtually eliminates flying dust and debris.
Cuts metal conduit in seconds with a few turns of the crank and a twist of the conduit. Ample clearance between handle and body. Set conduit size for multiple cuts of the same size. No need to reset. Set blade adjustment with only a screwdriver. In-handle blade storage holds up to five spare blades. Weighs 4 pounds. Capacity: 14/2 to 10/4 BX 3/8" flexible metal conduit.
Punches mild steel up through 10 gauge, aluminum, fiberglass and plastic. Splits slugs for easier removal. Hole size is outside diameter of US conduit sizes. 1/2" conduit and pipe size is 7/8" actual hole size, 3/4" conduit and pipe size is 1.115" actual hole size. Punch unit includes punch, die and draw stud. Uses standard Greenlee dies and draw studs. Use with battery, hydraulic, ratchet or manual drivers.
For aggressive chip removal in many types of woods. Screw point for easy starting and pulling through wood. Hole in bit for attaching pulling grip. With screw point removed, this bit can be ground to function like a standard combination bit.
Split tip design penetrates through steel faster, resisting walking or skidding even on round surfaces. Balanced, double-flute construction of these bits require less pressure. Designed and manufactured in USA. Hole sizes for No.36414 (SKU 149.9490): 7/8", 1-1/8", 1.201", 1-7/32", 1-1/2", 1-3/8". Hole sizes for No.34403 (SKU 361.4450): 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16", 7/8".
Drill/tap high-speed steel 6-32 to 1/4-20 six piece drill/tap set, split point. High quality hex shank to ensure strong connection to drill chuck. Complete hole drilling, tapping and deburring/countersinking in one operation with power drill. Designed to tap up to 10 gauge metal. Back taper or deburr/countersink beyond tap to prevent thread damage from over-drilling.Quick change adaptor included.