Protective coating that provides a waterproof barrier over the existing roof surface. May be used over composition and built-up roofs. Fiber-reinforced, liquid brush grade. Covers approximately 50 sq ft per gallon.
A thin liquid applied coating designed to seal and penetrate exterior concrete and masonry surfaces while providing a moisture barrier. It can also be used as an anti-corrosive coating for below grade steel or metal piping. Seals and protects wood footings from decay and termites. Covers approximately 70 sq. ft. per gallon.
Used on edging and flashings, weathered composition roofing, concrete, and masonry surfaces prior to the use of solvent based asphalt coatings or adhesives. Covers 33 sq. ft. per can depending on porosity of surface.
Designed to provide maximum adhesion to all surfaces. Its ability to expand and contract with the roof provides long-lasting protection and provides an excellent surface for application of Kool Seal Elastomeric Finish Coats. Provides maximum adhesion to all surfaces.
A heavy bodied cutback asphalt coating, reinforced with synthetic fibers. The coating cures to a tough, weather resistant film. It has good adhesion to brick, concrete and steel, and because of its ability to retain its pliability, this coating resists damage which may result from expansion and contraction caused by weather, temperature variations, and normal building vibrations. Excellent material for surfacing most asphalt based or metal roofs. It is recommended for resurfacing weathered asphalt roof surfaces. Aged asphalt roof surfaces are rejuvenated as the coating penetrates the worn asphalt substrates helping to restore its original properties. NOT recommended for use with coal tar roofs. Approximately 50 sq. ft. per gallon. Coverage rate varies depending on texture and porosity of surface.
For gutters and flashings. Designed to penetrate and saturate flat built-up and composition roofs. Provides a tough, durable, weather-resistant film. Contains non-mineral fibers. Can be used at lower temperatures. Not formulated for use on any surface other than horizontal FLAT. In hot weather, this product may flow from sloped surfaces. Not recommended for use on wood or asphalt shingles. Covers 100 sq. ft per 1.5 gallons. Depending on texture and porosity of surface. Not for sale in California. Black.
Brush or squeegee grade, waterproof adhesive made from asphalt, solvents, and organic fibers. Designed for bonding layers of asphalt coated base sheets. Eliminates burn and fire hazards of hot asphalt. U.L. Class A in a variety of roof systems. Use in applications with 25# or heavier asphalt-coated fiberglass base sheets, conventional mineral surface cap sheet, polyester fabric and bonding gravel or granule surfacing. Coverage varies with smoothness and porosity of surface coated.
Use for resurfacing and rejuvenating old, worn roofs. Resaturates and extends roof life. Use on asphalt roofs, metal roofs and composition roofs. Heavy-bodied asphalt coating, reinforced with non-asbestos fibers. Cures to a tough, flexible, weather resistant film. Resists damage from minor expansion and contraction by weather, temperature, and normal building vibration. Covers 60-100 per sq. ft. per gallon depending on surface type. Not for sale in California.
Use as a protective roof coating for new or existing composition roofs with smooth surfaces, as a base coat for reflective coatings, waterproofing adhesive for polyester systems, and as an anti-corrosive protection for metal roofs, steel structures, pipes, and tanks above or below ground level. Solvent free, asphalt emulsified with Bentonite clay and water. Applied cold, non-flammable while wet, corrosion-resistant, and waterproof when dry. Does not crack, run, or sag under extreme weather conditions. Complies with ASTM D-1227-95 Type III, Class I. U.L Classified. FM approved. Covers approximately 100 sq ft per 3-4 gallons when applied as one coat.
Cures to a tough, flexible, weather resistant film. Use for resurfacing and rejuvenating old, worn out flat roofs. Use on low slope asphalt roofs, metal roofs and composition roofs or adjoining concrete, brick and steel surfaces. Covers 100 sq. ft per 1.5 to 2 gallons on smooth surface. Coverage varies with surface texture.
A premium, highly flexible, white acrylic latex roof coating featuring a thick, high-hide formula. Reduces heat build-up and expands and contracts to resist cracking and peeling. Provides a protective barrier which reflects the sun?s heat and destructive UV rays. Covers approximately 50-75 sq. ft. per gallon per coat. Meets Energy Star performance ratings.
Forms a thick, rubber-like blanket of protection. Reduces interior temperatures. Seals and protects.
A flexible acrylic coating that resists cracking and peeling while extending the life of the roofing substrate. Provides a protective barrier which reflects the sun's heat and destructive UV rays. This helps to cool roof surfaces and may cause a reduction of interior temperatures. Covers approximately 50-75 sq ft per gallon per coat.
Specially formulated to resist mildew in hot humid climates. Reflects sun's heat and UV rays. Reduces air-conditioning cost and lowers roof and interior temperatures. Apply brush, roller or spray application. Apply two coats of 1 gallon per 100 sq. ft. for each coat. Allow it to dry between 2 coats.
Seamless rubberized asphalt membrane, for use in waterproofing or dampproofing concrete and masonry surfaces above and below grade. Excellent adhesion to most concrete surfaces such as concrete, brick, stone, wood, or metal. Retains flexibility in wide temperature range. Cold applied by trowel, brush, or spray; requires no special equipment such as kettles. Non-flammable. Coverage: Apply at a rate of 25 sq. ft. per gallon for a wet film thickness of 64 mils (dry film thickness of 45 mils). Dries to touch in 8 hours, sets in approximately 24 hours.
Ponding water resistant, no primer needed, energy efficient releases 91 percent of the sun's heat. Expands and contracts without cracking.
Use to protect buildings from the elements for years. Reflects 90-percent plus of the sun's rays. Forms a thick-rubber-like blanket of protection. Expands and contracts. Protects against moisture. Mildew and algae resistant when cured.
Advanced waterproofing technology, reduces heat-build up. Professional grade product forms a thick, rubberized shield that expands and contracts to prevent cracking and roof damage. Provides a highly protective barrier which reflects the sun?s UV rays. Covers approximately 50-75 sq. ft. per gallon per coat. Meets Energy Star performance ratings.
Use to protect buildings from the elements for years. Reflects 90-percent plus of the sun's rays. Designed to be durable in any climate. Forms a thick-rubber-like blanket of protection. Expands and contracts. Clings to your roof in all temperatures. Protects against moisture. Mildew and algae resistant when cured. Environmentally compliant. Helps to absorb sound.